Hunterdon County delivery area
Metal Panels and Sheet Metal Delivered to Hunterdon County, NJ
Metal panels for Hunterdon County, NJ go onto farmhouses, bank barns, equipment sheds, Delaware River storefronts and newer homes on large lots. We roll-form AG and PBR panels, cut standing seam to length and form trim and flashing in our New Brunswick shop. The order is delivered to the job or ready for pickup.
- Owner's 26+ years in metal
- Delivery or shop pickup
- Free written quotes
Can a New Brunswick shop deliver to a Hunterdon farm?
Yes. Hunterdon sits well inside our delivery area, which reaches about a 5-hour drive from the shop, and the delivery cost is quoted with the order.
Panels are cut to the lengths on your cut list and trims are formed before the order leaves. If the barn sits at the end of a long farm lane, describe the access and the longest panel when you request a quote. Builders who prefer to haul their own can pick up during Monday–Friday 7 AM–5 PM.
- Written quotes within 24-48 hours of receiving a cut list, sketch or plans
- Standing seam and trim typically take 1-2 days, depending on color and gauge; barn panel lead time is on your quote
- No minimum order, so one run-in shed is fine; custom colors carry a minimum quantity
- Have a lower written quote for the same parts? Send it with your request and we will match or beat it.
Which panels suit Hunterdon barns and pole buildings?
Exposed-fastener panels are the practical choice for most farm buildings, because they span between purlins or girts and go up quickly. Three profiles cover most barn orders.
AG panels
Run on our AG roll former, with about 36 inches of coverage, which is typical for AG profiles. A common pick for pole barns and run-in sheds; see barn and pole-building panels.
PBR panels
AMP PBR is 1-1/4 inch deep with 36 inches of coverage and a purlin-bearing leg, in 24 or 22 gauge steel, or 26 gauge for agricultural use on request.
7.2 Rib
The AMP 7.2 Rib has 1-1/2 inch ribs at 7.2 inches on center and 36 inches of coverage, for larger farm and commercial buildings.
Our post on AG panel vs PBR panel compares the two, and corrugated panels suit small outbuildings that should look traditional. On a low-pitch shed, send the pitch with the cut list so we can check it before quoting.
What do Hunterdon farmhouses and country homes need?
Standing seam is a common choice for a house you plan to keep, because the fasteners are hidden and the panels move on clips. Hunterdon is a county of owner-occupants, with an owner-occupied housing rate of 85.1 percent for 2020 to 2024, per Census QuickFacts.
Older farmhouses need more than panels: flashing for stone chimneys, chimney caps, box gutter liners and K-style gutters. Outbuildings and additions can take seamless metal siding in a board-and-batten style, roll-formed to the full length of each wall.
Hunterdon is in climate zone 5A, and state guidance asks for an address-specific ground snow load with a 35 psf fallback; our snow guard guide covers retention over porches and doors.
What do the Delaware River towns need?
Careful roof-edge metal for older buildings. Lambertville, Stockton, Frenchtown and Milford line the river with older commercial blocks, churches and closely spaced houses.
Their roofs take box gutter liners, metal coping and counter-flashing, plus 16 oz copper or zinc for bays and porch roofs. In a locally designated historic district, the town may review exterior changes, so check before ordering a material or color.
Hunterdon County towns on our delivery list
Alexandria, Bethlehem, Bloomsbury, Califon, Clinton (Town), Clinton Township, Delaware Township, East Amwell, Flemington (the county seat), Franklin Township, Frenchtown, Glen Gardner, Hampton, High Bridge, Holland, Kingwood, Lambertville, Lebanon Borough, Lebanon Township, Milford, Raritan Township, Readington, Stockton, Tewksbury, Union Township and West Amwell.
Hunterdon County questions
Do you make metal panels for barns and pole buildings in Hunterdon County?
Yes. AG, PBR, 7.2 Rib and corrugated panels for barns, sheds and equipment buildings, plus standing seam for houses, each made to the lengths on your builder’s cut list.
What gauge are PBR panels for a barn?
AMP PBR runs in 24 or 22 gauge steel as standard, with 26 gauge for agricultural use on request. Coverage is 36 inches.
Can you deliver long panels to a farm at the end of a lane?
Describe the access and the longest panel on the order when you request a quote, and we answer for that site. If a delivery does not suit the lane, the order can be picked up at our New Brunswick shop.
Can exposed-fastener panels go on a low-slope shed roof?
Sometimes. The model residential code sets 3:12 as the minimum for lapped panels without lap sealant, or 1/2:12 with applied sealant, and panel makers may require more. Send the pitch and we check it before we quote.
Is there a minimum order for a small shed?
No. There is no minimum order. Only custom (non-stock) colors carry a minimum quantity.
Request a quote
Tell us what you need: the product, the metal and finish, and your dimensions or cut list. Attach a photo, sketch or cut list if you have one. We reply with a written quote within 24-48 hours. Delivery within about five hours of our New Brunswick shop, or pickup.
Or text a photo or sketch with dimensions to (732) 236-8750
Prefer to talk now? Call (732) 201-5224, Monday–Friday 7 AM–5 PM. Text us a photo or sketch Fully insured
Hunterdon County orders
Ordering panels for a barn, farmhouse or river-town building?
Send the address, the building type and a cut list or plans, or text us a photo of a sketch with measurements. Expect a written quote or questions within 24-48 hours. Neighboring Somerset County and Mercer County are on the delivery area as well.